manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 416

 

10-48

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Signaling Events and Alarms

SIGNALING (89)

To troubleshoot and correct the cause of the alarm, refer to the 

“Gatekeeper not 

Available/Reachable—Signaling (89)” section on page 10-141

.

SIGNALING (90)

To troubleshoot and correct the cause of the alarm, refer to the 

“Alternate Gatekeeper is not 

Responding—Signaling (90)” section on page 10-141

.

DESCRIPTION

Gatekeeper not Available/Reachable 

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

0

DATAWORDS

Gateway ID–STRING [32]

 

Gatekeeper ID–STRING [32]

 

GK TSAP Addr–STRING [32]

PRIMARY

 

CAUSE

The gatekeeper is not available or is unreachable.

PRIMARY

 

ACTION

Check network connectivity. Check to ensure that the gatekeeper (GK) is reachable by trying to ping 
GK IP address. If reachable, then check to ensure that the GK is configured up.

DESCRIPTION

Alternate Gatekeeper is not Responding

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

0

DATAWORDS

Gateway ID–STRING [32]

 

Gatekeeper ID–STRING [32]

 

GK TSAP Addr–STRING [32]

PRIMARY

 

CAUSE

The alternate gatekeeper is not responding.

PRIMARY

 

ACTION

Check network connectivity. Check to ensure that the alternate GK is reachable by trying to ping the 
alternate GK IP address. If reachable, then check to ensure that the alternate GK is configured up.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands