manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 21

 

Contents

xxi

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Mate Changeover Timeout—Maintenance (8)

     

7-97

Local Initialization Failure—Maintenance (9)

     

7-97

Local Initialization Timeout—Maintenance (10)

     

7-97

Process Manager: Process has Died—Maintenance (18)

     

7-97

Process Manager: Process Exceeded Restart Rate—Maintenance (19)

     

7-98

Lost Connection to Mate—Maintenance (20)

     

7-98

Network Interface Down—Maintenance (21)

     

7-98

Process Manager: Process Failed to Complete Initialization—Maintenance (23)

     

7-98

Process Manager: Restarting Process—Maintenance (24)

     

7-99

Process Manager: Going Faulty—Maintenance (26)

     

7-99

Process Manager: Binary Does not Exist for Process—Maintenance (40)

     

7-99

Number of Heartbeat Messages Received is Less Than 50% of Expected—Maintenance (42)

     

7-99

Process Manager: Process Failed to Come Up in Active Mode—Maintenance (43)

     

7-99

Process Manager: Process Failed to Come Up in Standby Mode—Maintenance (44)

     

7-100

Application Instance State Change Failure—Maintenance (45)

     

7-100

Thread Watchdog Counter Expired for a Thread—Maintenance (47)

     

7-100

Index Table Usage Exceeded Minor Usage Threshold Level—Maintenance (48)

     

7-100

Index Table Usage Exceeded Major Usage Threshold Level—Maintenance (49)

     

7-101

Index Table Usage Exceeded Critical Usage Threshold Level—Maintenance (50)

     

7-101

A Process Exceeds 70% of Central Processing Unit Usage—Maintenance (51)

     

7-101

The Central Processing Unit Usage is Over 90% Busy—Maintenance (53)

     

7-101

The Five Minute Load Average is Abnormally High—Maintenance (55)

     

7-102

Memory and Swap are Consumed at Critical Levels—Maintenance (57)

     

7-102

No Heartbeat Messages Received Through the Interface—Maintenance (61)

     

7-102

Link Monitor: Interface Lost Communication—Maintenance (62)

     

7-103

Outgoing Heartbeat Period Exceeded Limit—Maintenance (63)

     

7-103

Average Outgoing Heartbeat Period Exceeds Major Alarm Limit—Maintenance (64)

     

7-103

Disk Partition Critically Consumed—Maintenance (65)

     

7-103

Disk Partition Significantly Consumed—Maintenance (66)

     

7-104

The Free Inter-Process Communication Pool Buffers Below Minor Threshold—Maintenance 
(67)

     

7-104

The Free Inter-Process Communication Pool Buffers Below Major Threshold—Maintenance 
(68)

     

7-104

The Free Inter-Process Communication Pool Buffers Below Critical Threshold—Maintenance 
(69)

     

7-104

The Free Inter-Process Communication Pool Buffer Count Below Minimum Required—Maintenance 
(70)

     

7-105

Local Domain Name System Server Response Too Slow—Maintenance (71)

     

7-105

External Domain Name System Server Response Too Slow—Maintenance (72)

     

7-105

External Domain Name System Server not Responsive—Maintenance (73)

     

7-105

Local Domain Name System Service not Responsive—Maintenance (74)

     

7-105

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands