manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 108

 

3-2

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 3      Billing Troubleshooting

Billing Events and Alarms

Billing Events and Alarms

This section provides a brief overview of the billing events and alarms for the Cisco BTS 10200 
Softswitch in numerical order. 

Table 3-1

 lists all of the billing events and alarms by severity.

Note

Click the Billing message number in 

Table 3-1

 to display information about the event or alarm.

Table 3-1

Billing Events and Alarms by Severity 

Critical

Major

Minor

Warning

Info

Not Used

BILLING (4)

BILLING (3)

BILLING (2)

BILLING (14)

BILLING (1)

BILLING (9)

BILLING (7)

BILLING (6)

BILLING (40)

BILLING (42)

BILLING (5)

BILLING (10)

BILLING (13)

BILLING (8)

BILLING (41)

BILLING (36)

BILLING (11)

BILLING (35)

BILLING (15)

BILLING (45)

BILLING (57)

BILLING (12)

BILLING (49)

BILLING (29)

BILLING (46)

BILLING (59)

BILLING (16)

BILLING (52)

BILLING (30)

BILLING (47)

BILLING (17)

BILLING (55)

BILLING (31)

BILLING (53)

BILLING (18)

BILLING (56)

BILLING (32)

BILLING (19)

BILLING (33)

BILLING (20)

BILLING (37)

BILLING (21)

BILLING (38)

BILLING (22)

BILLING (44)

BILLING (23)

BILLING (48)

BILLING (24)

BILLING (54)

BILLING (25)

BILLING (58)

BILLING (26)

BILLING (27)

BILLING (28)

BILLING (34)

BILLING (39)

BILLING (43)

BILLING (50)

BILLING (51)

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands