manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 765

 

16-17

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 16      Disaster Recovery Procedures

Recovering the Element Management System Database from Another Database

Step 4

Clean up the restored files in 

/opt/oraback

 directory to claim the disk space back.

ls /opt/oraback/*200201100200*

ls /opt/oraback/*200201101800*

rm /opt/oraback/*200201100200*

rm /opt/oraback/*200201101800*

Step 5

Resume operations.

You are now ready to shut down the Oracle database and start the platform and cron process.

Step 6

Log in as 

root

 or 

su - root

Step 7

Enter the following commands:

su – root

platform stop –i oracle 

platform start

svcadm enable svc:/system/cron

nodestat

The recovery of the primary EMS database is now complete. To recover the secondary EMS database, 
copy data from the primary EMS database. Refer to the 

“Recovering the Element Management System 

Database from Another Database”

.

Recovering the Element Management System Database from 
Another Database

This section provides the procedures to recover one corrupted EMS database from another active 
database.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands