Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 495

Page: 495 / 874

10-127

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10 Signaling Troubleshooting

Troubleshooting Signaling Alarms

This section provides the information needed to monitor and correct signaling alarms.

Table 10-3

lists

all of the signaling alarms in numerical order and provides cross reference to each subsection in this
section.

Table 10-3

BTS 10200 Signaling Alarms

Alarm Type

Alarm Name

Alarm Severity

SIGNALING(7)

Socket Failure—Signaling (7)

MAJOR

SIGNALING(8)

Session Initiation Protocol Message Receive Failure—Signaling (8)

MAJOR

SIGNALING(9)

Timeout on Internet Protocol Address—Signaling (9)

MAJOR

SIGNALING(10)

Failed to Send Complete Session Initiation Protocol Message—Signaling (10)

MINOR

SIGNALING(11)

Failed to Allocate Session Initiation Protocol Control Block—Signaling (11)

MAJOR

SIGNALING(12)

Feature Server is not Up or is not Responding to Call Agent—Signaling (12)

CRITICAL

SIGNALING(13)

Signaling System 7 Signaling Link Down—Signaling (13)

MAJOR

SIGNALING(14)

Link is Remotely Inhibited—Signaling (14)

MINOR

SIGNALING(15)

Link is Locally Inhibited—Signaling (15)

MINOR

SIGNALING(16)

Link is Congested—Signaling (16)

MINOR

SIGNALING(17)

Link: Local Processor Outage—Signaling (17)

MINOR

SIGNALING(18)

Link: Remote Processor Outage—Signaling (18)

MINOR

SIGNALING(19)

Link Set Inaccessible—Signaling (19)

MAJOR

SIGNALING(20)

Link Set Congestion—Signaling (20)

MAJOR

SIGNALING(21)

Route Set Failure—Signaling (21)

MAJOR

SIGNALING(22)

Route Set Congested—Signaling (22)

MINOR

SIGNALING(23)

Destination Point Code Unavailable—Signaling (23)

MAJOR

SIGNALING(24)

Destination Point Code Congested—Signaling (24)

MINOR

SIGNALING(36)

Trunk Locally Blocked—Signaling (36)

MINOR

SIGNALING(40)

Trunk Remotely Blocked—Signaling (40)

MAJOR

SIGNALING(59)

Auto State Change for Integrated Services Digital Network Trunk Group by Media
Gateway—Signaling (59)

MAJOR

SIGNALING(63)

Media Gateway/Termination Faulty—Signaling (63)

MAJOR

SIGNALING(64)

Media Gateway Adapter Running out of Shared Memory Pools—Signaling (64)

CRITICAL

SIGNALING(65)

Media Gateway Adapter Running out of Heap Memory—Signaling (65)

CRITICAL

SIGNALING(66)

Call Agent Internal Error (Because of Which Media Gateway Adapter has to Start
Automatically)—Signaling (66)

MAJOR

SIGNALING(68)

Trunking Gateway Endpoints are out of Service at the Gateway—Signaling (68)

MAJOR

SIGNALING(69)

Call Agent is not Up or is not Responding to the Feature Server—Signaling (69)

CRITICAL

SIGNALING(75)

Signaling System 7 Stack not Ready—Signaling (75)

CRITICAL

SIGNALING(78)

Integrated Services Digital Network Single D-channel Down for Non-Facility
Associated Signaling—Signaling (78)

MINOR

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands