Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 322

Page: 322 / 874

7-90

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 7 Maintenance Troubleshooting

Troubleshooting Maintenance Alarms

This section provides the information needed to troubleshoot and correct maintenance alarms.

Table 7-3

lists all of the maintenance alarms in numerical order and provides cross reference to each subsection in
this section.

Table 7-3

BTS 10200 Maintenance Alarms

Alarm Type

Alarm Name

Alarm Severity

MAINTENANCE(3)

Local Side has Become Faulty—Maintenance (3)

MAJOR

MAINTENANCE(4)

Mate Side has Become Faulty—Maintenance (4)

MAJOR

MAINTENANCE(5)

Changeover Failure—Maintenance (5)

MAJOR

MAINTENANCE(6)

Changeover Timeout—Maintenance (6)

MAJOR

MAINTENANCE(7)

Mate Rejected Changeover—Maintenance (7)

MAJOR

MAINTENANCE(8)

Mate Changeover Timeout—Maintenance (8)

MAJOR

MAINTENANCE(9)

Local Initialization Failure—Maintenance (9)

MAJOR

MAINTENANCE(10)

Local Initialization Timeout—Maintenance (10)

MAJOR

MAINTENANCE(18)

Process Manager: Process has Died—Maintenance (18)

MINOR

MAINTENANCE(19)

Process Manager: Process Exceeded Restart Rate—Maintenance (19)

MAJOR

MAINTENANCE(20)

Lost Connection to Mate—Maintenance (20)

MAJOR

MAINTENANCE(21)

Network Interface Down—Maintenance (21)

MAJOR

MAINTENANCE(23)

Process Manager: Process Failed to Complete Initialization—Maintenance (23)

MAJOR

MAINTENANCE(24)

Process Manager: Restarting Process—Maintenance (24)

MINOR

MAINTENANCE(26)

Process Manager: Going Faulty—Maintenance (26)

MAJOR

MAINTENANCE(40)

Process Manager: Binary Does not Exist for Process—Maintenance (40)

CRITICAL

MAINTENANCE(42)

Number of Heartbeat Messages Received is Less Than 50% of
Expected—Maintenance (42)

MAJOR

MAINTENANCE(43)

Process Manager: Process Failed to Come Up in Active Mode—Maintenance (43)

CRITICAL

MAINTENANCE(44)

Process Manager: Process Failed to Come Up in Standby Mode—Maintenance
(44)

CRITICAL

MAINTENANCE(45)

Application Instance State Change Failure—Maintenance (45)

MAJOR

MAINTENANCE(47)

Thread Watchdog Counter Expired for a Thread—Maintenance (47)

CRITICAL

MAINTENANCE(48)

Index Table Usage Exceeded Minor Usage Threshold Level—Maintenance (48)

MINOR

MAINTENANCE(49)

Index Table Usage Exceeded Major Usage Threshold Level—Maintenance (49)

MAJOR

MAINTENANCE(50)

Index Table Usage Exceeded Critical Usage Threshold Level—Maintenance (50)

CRITICAL

MAINTENANCE(51)

A Process Exceeds 70% of Central Processing Unit Usage—Maintenance (51)

MAJOR

MAINTENANCE(53)

The Central Processing Unit Usage is Over 90% Busy—Maintenance (53)

CRITICAL

MAINTENANCE(55)

The Five Minute Load Average is Abnormally High—Maintenance (55)

MAJOR

MAINTENANCE(57)

Memory and Swap are Consumed at Critical Levels—Maintenance (57)

CRITICAL

MAINTENANCE(61)

No Heartbeat Messages Received Through the Interface—Maintenance (61)

CRITICAL

MAINTENANCE(62)

Link Monitor: Interface Lost Communication—Maintenance (62)

MAJOR

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands