manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 503

 

10-135

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Troubleshooting Signaling Alarms

Route Set Failure—Signaling (21)

The Route Set Failure alarm (major) indicates that the specified route set has a experienced a failure. 
The primary cause of the alarm is the specified route set has experienced a failure. To correct the primary 
cause of the alarm, verify that the processing complex supporting the route set is functional. Monitor 
event reports at the network level to determine the failing component and verify its restoral to service.

Route Set Congested—Signaling (22)

The Route Set Congested alarm (minor) indicates that the specified route set is congested. The primary 
of the alarm is that the specified route set is experiencing congestion. To correct the primary cause of 
the alarm, monitor event reports at the network level to determine if the traffic load on the specified SS7 
link set is too high on the local end, or if the remote end is lagging in processing the traffic. Verify that 
the SS7 link set has not degraded in quality. Verify that the traffic load has not become unbalanced if 
multiple SS7 link sets are used. Verify that local SS7 signaling adapter process is running normally.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands