manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 670

 

15-44

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

Network Loopback Test for Network-based Call Signaling/Media Gateway Control Protocol Endpoints

Dedicated NLB Testing Device Configuration Example

Note

The following is an example of provisioning a dedicated testing trunk-grp for testing network loop-back 
on a subscriber line. Change TEST-LINE-TYPE to different values (other than NTE) to change test 
origination type.

Use the following procedure as a dedicated NLB testing device configuration example.

Step 1

Add MGW profile.

add mgw-profile id=BRIX; vendor=Tollgrade; mgcp-version=mgcp_1_0; MGCP-VARIANT=NCS-1-0;

Step 2

Add cas-tg-profile.

add cas-tg-profile id=BRIX_TG; sig-type=LINE; TEST-LINE=Y; TEST-LINE-TYPE=NLB-LINE-TEST

Step 3

Add MGW.

add mgw id=brix1; tsap-addr=<mgw DNS / IP address>; mgw-profile-id=BRIX; type=TGW; 

call-agent id=CA146;

Step 4

Add trunk-grp.

add trunk-grp id=100; call-agent-id=CA146; tg-type=CAS; cas-tg-profile=BRIX_TG; 

mgcp-pkg-type=LINE

Step 5

Add termination.

add termination prefix=aaln/; port-start=1; port-end=2; type=TRUNK; mgw-id=c925.172; 

Step 6

Add trunk.

add trunk termination-prefix=aaln/; termination-port-start=1; termination-port-end=2; 

cic-start=1; cic-end=2; tgn-id=100

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands