Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 724

Page: 724 / 874

15-98

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15 Diagnostic Tests

Enhanced Traffic Measurement

SIS_INFO_RX

The number of SIP INFO messages the reporting call agent or feature server received.

SIS_INFO_TX

The number of SIP INFO messages the reporting call agent or feature server sent.

SIS_NOTIFY_RX

The number of SIP NOTIFY messages the reporting call agent or feature server
received.

SIS_NOTIFY_TX

The number of SIP NOTIFY messages the reporting call agent or feature server sent.

SIS_100_RX

The number of 100 class (TRYING) messages the reporting call agent or feature server
received.

SIS_100_TX

The number of 100 class (TRYING) messages the reporting call agent or feature server
sent.

SIS_18x_RX

The number of 18x class (INFORMATIONAL) messages the reporting call agent or
feature server received.

SIS_18x_TX

The number of 18x class (INFORMATIONAL) messages the reporting call agent or
feature server sent.

SIS_200_RX

The number of 200 class (SUCCESS) messages the reporting call agent or feature
server received.

SIS_200_TX

The number of 200 class (SUCCESS) messages the reporting call agent or feature
server sent.

SIS_3xx_RX

The number of 3xx class (REDIRECTION) messages the reporting call agent or
feature server received.

SIS_3xx_TX

The number of 3xx class (REDIRECTION) messages the reporting call agent or
feature server sent.

SIS_4xx_RX

The number of 4xx class (REQUEST FAILURES) messages the reporting call agent
or feature server received.

SIS_4xx_TX

The number of 4xx class (REQUEST FAILURES) messages the reporting call agent
or feature server sent.

SIS_5xx_RX

The number of 5xx class (SERVER FAILURES) messages the reporting call agent or
feature server received.

SIS_5xx_TX

The number of 5xx class (SERVER FAILURES) messages the reporting call agent or
feature server sent.

SIS_6xx_RX

The number of 6xx class (GLOBAL FAILURES) messages the reporting call agent or
feature server received.

SIS_6xx_TX

The number of 6xx class (GLOBAL FAILURES) messages the reporting call agent or
feature server sent.

SIS_7xx_RX

The number of 7xx class (RESERVED) messages the reporting call agent or feature
server received.

SIS_7xx_TX

The number of 7xx class (RESERVED) messages the reporting call agent or feature
server sent.

SIS_PROV_RSP_RETRAN_RX

The number of SIP provisioning response retransmission messages the reporting call
agent or feature server received.

SIS_PROV_RSP_RETRAN_TX

The number of SIP provisioning response retransmission messages the reporting call
agent or feature server sent.

Table 15-12

Session Initiation Protocol Counters (continued)

Counter Label

Counter Context

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands