Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 277

Page: 277 / 874

7-45

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 7 Maintenance Troubleshooting

Maintenance Events and Alarms

MAINTENANCE (84)

To troubleshoot and correct the cause of the alarm, refer to the

“Swap Space Below Major

Threshold—Maintenance (84)” section on page 7-106

MAINTENANCE (85)

To troubleshoot and correct the cause of the alarm, refer to the

“Swap Space Below Critical

Threshold—Maintenance (85)” section on page 7-106

DESCRIPTION

Swap Space Below Major Threshold

SEVERITY

MAJOR

THRESHOLD

THROTTLE

DATAWORDS

Major Threshold (MB)–FOUR_BYTES

Current Value (MB)–FOUR_BYTES

PRIMARY

CAUSE

Too many processes are running.

PRIMARY

ACTION

Stop the proliferation of executables (processes/shell-procedures).

SECONDARY

CAUSE

File spaces /tmp or /var/run are over-used.

SECONDARY

ACTION

Cleanup the file systems.

DESCRIPTION

Swap Space Below Critical Threshold

SEVERITY

CRITICAL

THRESHOLD

THROTTLE

DATAWORDS

Critical Threshold (M–FOUR_BYTES

Current Value (MB)–FOUR_BYTES

PRIMARY

CAUSE

Too many processes are running.

PRIMARY

ACTION

Restart the BTS 10200 software or reboot the system.

SECONDARY

CAUSE

File spaces /tmp or /var/run are over-used.

SECONDARY

ACTION

Cleanup the file systems.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands