manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 202

 

6-8

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 6      Database Troubleshooting

Database Events and Alarms

DATABASE (8)

To troubleshoot and correct the cause of the alarm, refer to the 

“Element Management System Database 

Tablespace is Out of Free Space—Database (8)” section on page 6-31

.

DATABASE (9)

To troubleshoot and correct the cause of the alarm, refer to the 

“Urgent: Element Management System 

Database Archive Log Directory is Getting Full—Database (9)” section on page 6-31

.

DESCRIPTION

Element Management System Database Tablespace is Out of Free Space (EMS Database Tablespace 
is Out of Free Space)

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

0

DATAWORDS

Host Name–STRING [30]

 

Database Name–STRING [10]

 

Tablespace Name–STRING [30]

 

Total Free Space–TWO_BYTES

 

Time Stamp–STRING [20] 

PRIMARY

 

CAUSE

An increase data volume or transactions has occurred.

PRIMARY

 

ACTION

Add more space to the tablespace.

DESCRIPTION

Urgent: Element Management System Database Archive Log Directory is Getting Full (URGENT: 
EMS Database Archive Log Directory is Getting Full)

SEVERITY

CRITICAL

THRESHOLD

100

THROTTLE

0

DATAWORDS

Host Name–STRING [30]

 

Database Name–STRING [10]

 

Directory Name–STRING [100]

 

Free Space–TWO_BYTES

 

Time Stamp–STRING [20]

PRIMARY

 

CAUSE

The transaction volume has increased.

PRIMARY

 

ACTION

Backup and cleanup the archive log files.

SECONDARY

 

ACTION

Add more space to the archive log directory.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands