manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 479

 

10-111

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Monitoring Signaling Events

Remote H323 Gateway is not Reachable—Signaling (86)

The Remote H323 Gateway is not Reachable alarm (major) indicates that the remote H323 gateway is 
not reachable. To troubleshoot and correct the cause of the Remote H323 Gateway is not Reachable 
alarm, refer to the 

“Remote H323 Gateway is not Reachable—Signaling (86)” section on page 10-141

.

H323 Message Parsing Error—Signaling (87)

The H323 Message Parsing Error alarm (major) indicates that a H323 message parsing error has 
occurred. To troubleshoot and correct the cause of the H323 Message Parsing Error alarm, refer to the 

“H323 Message Parsing Error—Signaling (87)” section on page 10-141

.

H323 Message Encoding Error—Signaling (88)

The H323 Message Encoding Error alarm (major) indicates that a H323 message encoding error has 
occurred. To troubleshoot and correct the cause of the H323 Message Encoding Error alarm, refer to the 

“H323 Message Encoding Error—Signaling (88)” section on page 10-141

.

Gatekeeper not Available/Reachable—Signaling (89)

The Gatekeeper not Available/Reachable alarm (major) indicates that the gatekeeper is not available or 
the gatekeeper is not reachable. To troubleshoot and correct the cause of the Gatekeeper not 
Available/Reachable alarm, refer to the 

“Gatekeeper not Available/Reachable—Signaling (89)” section 

on page 10-141

.

Alternate Gatekeeper is not Responding—Signaling (90)

The Alternate Gatekeeper is not Responding alarm (major) indicates that the alternate gatekeeper is not 
responding. To troubleshoot and correct the cause of the Alternate Gatekeeper is not Responding alarm, 
refer to the 

“Alternate Gatekeeper is not Responding—Signaling (90)” section on page 10-141

.

Endpoint Security Violation—Signaling (91)

The Endpoint Security Violation alarm (major) indicates that an H323 security violation has occurred. 
To troubleshoot and correct the cause of the Endpoint Security Violation alarm, refer to the 

“Endpoint 

Security Violation—Signaling (91)” section on page 10-142

.

Invalid Call Identifier—Signaling (92)

The Invalid Call Identifier alarm (minor) indicates that the Call ID was invalid or changed mid-call. To 
troubleshoot and correct the cause of the Invalid Call Identifier alarm, refer to the 

“Invalid Call 

Identifier—Signaling (92)” section on page 10-142

.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands