manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 357

 

8-13

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 8      Operations Support System Troubleshooting

Troubleshooting Operations Support System Alarms

Troubleshooting Operations Support System Alarms

This section provides the information needed to monitor and correct OSS alarms. 

Table 8-3

 lists all of 

the OSS alarms in numerical order and provides cross reference to each subsection in this section.

Undefined Variable in Known Set—Operations Support System (2)

The Undefined Variable in Known Set alarm (major) indicates that there was not a definition for a data 
column that could be found in the database. The primary cause of the alarm is that there was no definition 
of a data column that could be found in the database. To correct the primary cause of the alarm, contact 
Cisco TAC for support.

Note

Refer to the 

“Obtaining Documentation and Submitting a Service Request” section on page lvi

 for 

detailed instructions on contacting Cisco TAC and opening a service request.

Undefined Data Column Identification—Operations Support System (3)

The Undefined Data Column Identification alarm (major) indicates that the database does not contain 
the required data column that was requested via the SNMP interface. The primary cause of the alarm is 
that the database does not contain the required data column that was requested via the SNMP interface. 
To correct the primary cause of the alarm, contact Cisco TAC for support.

Note

Refer to the 

“Obtaining Documentation and Submitting a Service Request” section on page lvi

 for 

detailed instructions on contacting Cisco TAC and opening a service request.

Table 8-3

BTS 10200 OSS Alarms 

Alarm Type

Alarm Name

Alarm Severity

OSS(2)

Undefined Variable in Known Set—Operations Support System (2)

MAJOR

OSS(3)

Undefined Data Column Identification—Operations Support System (3)

MAJOR

OSS(4)

Request Handler Instantiation Error—Operations Support System (4)

MAJOR

OSS(5)

Structured Query Language Error While Getting Statistics—Operations Support 
System (5)

MINOR

OSS(6)

Structured Query Language Connection Error—Operations Support System (6)

MAJOR

OSS(8)

No Reply Received from Destination—Operations Support System (8)

MINOR

OSS(9)

Simple Network Management Protocol Authentication Error—Operations Support 
System (9)

MINOR

OSS(10)

Queue Processing Module Database Management Index Failed with 
Error—Operations Support System (10)

MAJOR

OSS(14)

User Session Count Exceeds Major Threshold Limit—Operations Support System 
(14)

MAJOR

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands