manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 173

 

4-23

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 4      Call Processing Troubleshooting

Monitoring Call Processing Events

Monitoring Call Processing Events

This section provides the information needed to monitor and correct call processing events. 

Table 4-2

 

lists all of the call processing events in numerical order and provides cross reference to each subsection 
in this section.

Table 4-2

BTS 10200 Call Processing Events 

Event Type

Event Name

Event Severity

CALLP(1)

Test Report—Call Processing (1)

INFO

CALLP(8)

No Route Available for Called Number—Call Processing (8)

WARNING

CALLP(9)

No Route Available for Carrier Dialed—Call Processing (9)

INFO

CALLP(11)

Feature Server One Link Down—Call Processing (11)

MINOR

CALLP(12)

Feature Server Both Links Down—Call Processing (12)

CRITICAL

CALLP(13)

Network Access Server Create Connection Error—Call Processing (13)

INFO

CALLP(14)

Network Access Server Authentication Failure—Call Processing (14)

INFO

CALLP(15)

Cable Modem Termination System Easily Recognizable Identification Not Found in 
Media Gateway Table—Call Processing (15)

INFO

CALLP(16)

Route Index has No Trunk Group Assigned—Call Processing (16)

WARNING

CALLP(17)

Invalid Route Index Used—Call Processing (17)

WARNING

CALLP(18)

Unable to Play Announcement—Call Processing (18)

WARNING

CALLP(19)

Call Routed to Unprovisioned Subscriber—Call Processing (19)

WARNING

CALLP(20)

No Route or Trunk Group Available to Route Call—Call Processing (20)

WARNING

CALLP(21)

Call Released Due to Maximum Hop Counts Exceeded—Call Processing (21)

WARNING

CALLP(22)

Trunk Group Index Read Failure—Call Processing (22)

WARNING

CALLP(23)

Routing Error: Termination is Not a Subscriber—Call Processing (23)

WARNING

CALLP(24)

Invalid Route for Subscriber Index—Call Processing (24)

WARNING

CALLP(25)

Invalid Route Group for Subscriber Routing—Call Processing (25)

WARNING

CALLP(26)

Invalid Trunk Group for Subscriber Routing—Call Processing (26)

WARNING

CALLP(27)

Unable to Route: Blocked by Destination Subscriber Status—Call Processing (27)

WARNING

CALLP(28)

Route Name Does Not Exist—Call Processing (28)

WARNING

CALLP(29)

Routing Selection Failure—Call Processing (29)

WARNING

CALLP(30)

Customer-Originated Trace Test Failed—Call Processing (30)

WARNING

CALLP(31)

Call Authorization Failure—Call Processing (31)

WARNING

CALLP(32)

Country Code Dialing Plan Error—Call Processing (32)

WARNING

CALLP(33)

Invalid Call—Call Processing (33)

WARNING

CALLP(34)

Dial Plan Information Not Found for Digits Received—Call Processing (34)

WARNING

CALLP(35)

Dial Plan Information for Test Call Not Found—Call Processing (35)

WARNING

CALLP(36)

Invalid or Unknown Nature of Address—Call Processing (36)

WARNING

CALLP(37)

Call Failure—Call Processing (37)

WARNING

CALLP(38)

Release Cause 25 Exchange Routing Error Received—Call Processing (38)

MINOR

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands