manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 636

 

15-10

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

Integrated Services Digital Network Trunk Termination Tests

Integrated Services Digital Network Trunk Termination Tests

This section describes the tests that can be performed on Integrated Services Digital Network (ISDN) 
trunk terminations. All terminations must be in the MAINT state for testing.

Step 1

Force the ISDN trunk termination into MAINT state:

control isdn-trunk-termination tgn-id=17; mode=forced; target-state=maint;

Step 2

Display the Test Menu.

diag isdn-trunk-termination

Reply Example:

Reply: Diagnostic ISDN Trunk Group Menu.

=== 

(1) ISDN MGCP Connectivity Test

(2) ISDN Termination Connection Test

(3) ALL

Note

Test #1 tests if MGCP has access to the ISDN termination. 

 

Test #2 tests if there is a path to the device (ping). 

 

Test #3 performs tests 1 and 2.

Step 3

To perform a specific test, use the following examples as a guide.

diag isdn-trunk-termination test=1; tgn-id=17; cic=1;

Reply Example:

TRUNK DIAGNOSTIC TEST EXECUTED -> diag trunk

TG-NUM -> 17

CIC -> 1

TEST-TYPE -> ADM-MGW-MGCP-CONNECTIVITY-TEST

TEST-DURATION -> 0

RESULT -> TEST-SUCCESS

REASON -> PASSED: Reason: AUEP-NACK received with RespCode = 510

Reply: Diagnostic command executed.

diag isdn-trunk-termination test=2; tgn-id=17; cic=1;

Reply Example:

TRUNK DIAGNOSTIC TEST EXECUTED -> diag trunk

TG-NUM -> 17

CIC -> 1

TEST-TYPE -> ADM-TERM-CONNECTION-TEST

TEST-DURATION -> 0

RESULT -> TEST-SUCCESS

REASON -> PASSED: Reason: AUEP-NACK received with RespCode = 510

Reply: Diagnostic command executed.

Step 4

Force the ISDN trunk termination into MAINT state:

control isdn-trunk-termination tgn-id=17; mode=forced; target-state=maint;

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands