Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 292

Page: 292 / 874

7-60

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 7 Maintenance Troubleshooting

Maintenance Events and Alarms

MAINTENANCE (112)

To troubleshoot and correct the cause of the alarm, refer to

“Congestion Status—Maintenance (112)”

section on page 7-110

MAINTENANCE (113)

For additional information, refer to

“Central Processing Unit Load of Critical Processes—Maintenance

(113)” section on page 7-88

DESCRIPTION

Congestion Status

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

DATAWORDS

System MCL Level–ONE_BYTE

PRIMARY

CAUSE

A change has occurred in the system overload level.

PRIMARY

ACTION

If the reported level remains continuously high, adjust the system load or configuration.

DESCRIPTION

Central Processing Unit Load of Critical Processes (CPU Load of Critical Processes)

SEVERITY

INFO

THRESHOLD

100

THROTTLE

DATAWORDS

Factor Level–ONE_BYTE

Factor MCL–ONE_BYTE

PRIMARY

CAUSE

A change (increase/decrease) has occurred in the call processing load.

PRIMARY

ACTION

If the level remains continuously high, change the configuration or redistribute the call load.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands