manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 616

 

14-42

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 14      General Troubleshooting

Protocol Troubleshooting

Maintenance of a Call Agent Connected to an Integrated Services Digital Network Trunk Group

During system operations, the operator can use the CLI 

control

 command to switch the Call Agent into 

one of two states:

  •

ACTIVE-STANDBY

  •

STANDBY-ACTIVE

When the control command is entered on a Call Agent connected to an ISDN trunk group (D channel), 
the Call Agent switchover time is approximately 20 seconds. During all but the first 6 seconds of this 
switchover time, the ISDN D channel is temporarily down. However, the D channel comes back up, and 
the ISDN trunk group automatically returns to INS, when the switchover completes. 

Note

This switchover process does not have any impact on stable calls.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands