manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 800

 

17-10

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 17      Disk Replacement

Call Agent/Feature Server or Element Management System Disk 1 Replacement 

Call Agent/Feature Server or Element Management System Disk 
1 Replacement 

Note

The letter "x" in cxt0d0 or cxt1d0 throughout the procedure is referring to the SCSI controller ID of the 
system (either 0 or 1). To find out the controller ID, use the 

format

 command. 

Step 1

Login as root.

Step 2

Verify application status.

<hostname>#

nodestat

Note

If all platforms on this node are ACTIVE, then you need to switchover to STANDBY side using the CLI 
command.

Step 3

Stop all BTS 10200 platforms.

<hostname>#

platform stop all

Step 4

Perform the following commands to detach all submirror metadevice.

<hostname>#

metadetach –f d2 d1

<hostname>#

metadetach –f d14 d13

<hostname>#

metadetach –f d11 d10

<hostname>#

metadetach –f d5 d4

<hostname>#

metadetach –f d8 d7

Step 5

Perform the following commands to clear all submirror metadevice.

<hostname>#

metaclear d1

<hostname>#

metaclear d13

<hostname>#

metaclear d10

<hostname>#

metaclear d4

<hostname>#

metaclear d7

Step 6

Delete database replica on defective disk.

<hostname>#

metadb –d –f /dev/dsk/cxt1d0s4

Step 7

Verify that there is no existing metadevice on defective disk.

<hostname>#

metastat –p |grep cxt1d0

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands