manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 54

 

liv

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Preface

SIGNALING (169)

Session Initiation Protocol Element Provisioned with Service Enabled is 
Internally Disabled (SIP Element Provisioned with SRV Enabled is 
Internally Disabled)

SIGNALING (170)

Residential Gateway Endpoints are out of Service at the Gateway 
(Residential Gateway Endpoints are out of Service at the GW)

SIGNALING (171)

Residential Gateway Unreachable

SIGNALING (172)

Multimedia Terminal Adapter Effective-Aggr-Id Becomes Unavailable Due 
to its IP Address (MTA Effective-Aggr-Id Becomes Unavailable Due to its 
IP Address)

SIGNALING (173)

ENUM Server Domain Cannot be Resolved into Any IP Address

SIGNALING (174)

ENUM Server Unavailable

SIGNALING (175)

ENUM Server Farm Unavailable

SIGNALING (176)

No Resources Available to Launch ENUM Query

SIGNALING (177)

ISDN Unable to Restore D-Channel into In-Service Active State

STATISTICS (14)

MDII Trunk

STATISTICS (15)

Threshold Crossing Alert

STATISTICS (16)

Trunk Group has Reached the MDII Alarm Threshold

Table 1

New Events and Alarms (Release 4.5.1 to Release 5.0) (continued)

Type and Number

Description

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands