manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 493

 

10-125

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Monitoring Signaling Events

Session Initiation Protocol Element Provisioned with Service Enabled is 
Internally Disabled—Signaling (169)

The Session Initiation Protocol Element Provisioned with Service Enabled is Internally Disabled event 
functions as an informational alert that a SIP element was provisioned with SRV enabled and is 
associated to at least one or more Server Groups. The SRV flag will be assumed disabled. However, to 
resolve this informational message, provision the SRV flag disabled on the SIP element.

Residential Gateway Endpoints are out of Service at the Gateway—Signaling 
(170)

The Residential Gateway Endpoints are out of Service at the Gateway alarm (minor) indicates that the 
residential gateway has been administratively taken OOS using the command at the gateway. To 
troubleshoot and correct the primary cause of the Residential Gateway Endpoints are out of Service at 
the Gateway alarm, refer to the 

“Residential Gateway Endpoints are out of Service at the 

Gateway—Signaling (170)” section on page 10-158

.

Residential Gateway Unreachable—Signaling (171)

The Residential Gateway Unreachable alarm (minor) indicates that a MGCP signaling interop error has 
occurred with the residential media gateway. To troubleshoot and correct the primary cause of the 
Residential Gateway Unreachable alarm, refer to the 

“Residential Gateway Unreachable—Signaling 

(171)” section on page 10-158

.

Multimedia Terminal Adapter Effective-Aggr-Id Becomes Unavailable Due to 
Its IP Address—Signaling (172)

The Multimedia Terminal Adapter Effective-Aggr-Id Becomes Unavailable Due to Its IP Address alarm 
(major) indicates that the MTA has been moved to new subnet which is not provisioned, or provisioned 
with the aggr-id=NULL. To troubleshoot and correct the primary cause of the Multimedia Terminal 
Adapter Effective-Aggr-Id Becomes Unavailable Due to Its IP Address alarm, refer to the 

“Multimedia 

Terminal Adapter Effective-Aggr-Id Becomes Unavailable Due to Its IP Address—Signaling (172)” 
section on page 10-158

.

ENUM Server Domain Cannot be Resolved Into Any IP Address —Signaling 
(173)

The ENUM Server Domain Cannot be Resolved Into Any IP Address alarm (critical) indicates that a 
misconfiguration has occurred in the DNS configuration. To troubleshoot and correct the cause of the 
ENUM Server Domain Cannot be Resolved Into Any IP Address alarm, refer to the 

“ENUM Server 

Domain Cannot be Resolved Into Any IP Address —Signaling (173)” section on page 10-159

.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands