manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 389

 

10-21

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Signaling Events and Alarms

SIGNALING (32)

To monitor and correct the cause of the event, refer to the 

“Unanswered Group Reset 

Message—Signaling (32)” section on page 10-102

.

DESCRIPTION

Unanswered Group Reset Message (Unanswered GRS)

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

0

DATAWORDS

CIC Number–TWO_BYTES

 

TGN-ID–FOUR_BYTES

 

DPC–STRING [20]

 

OPC–STRING [20]

PRIMARY

 

CAUSE

Issued when a group reset (GRS) message was not acknowledged before the timer 23 (T23) expired 
for the associated CIC.

PRIMARY

 

ACTION

Verify that the SS7 signaling adapter processes is running normally. Verify that the call agent platform 
is active.

SECONDARY

 

ACTION

Verify that the SS7 interface hardware is in service. Verify that the associated SS7 signaling link is 
available.

TERNARY

 

ACTION

Verify that the T13 timer is set to an appropriate level.

SUBSEQUENT

 

ACTION

Verify that the SS7 link is not congested.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands