manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 727

 

15-101

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

BTS 10200 Status

Note

Both sides of one BTS 10200 network element use the same port.

You can run BTSSTAT from a non-BTS 10200 host, provided that the host can establish an SSL 
connection to the target BTS 10200 host. In this case, the BTS 10200 hosts should be specified in a 
configuration file. Users can specify a configuration file with the -f option as follows:

btsstat -f my_cfg_file

The user-provided configuration file must contain the tokens in 

Table 15-14

 along with the values of the 

corresponding host names. BTSSTAT ignores all other lines in the file.

You can use a command-line argument to specify nondefault port numbers to status for any of the BTS 
10200 network elements. The command-line options in 

Table 15-15

 are supported to specify the port 

numbers.

Table 15-14

BTSSTAT Configuration File Format 

Element

Setting

CA_SIDE_A_HN = 

 

CA_SIDE_B_HN = 

prica11

 

secca11

FSAIN_SIDE_A_HN = 

 

FSAIN_SIDE_B_HN = 

prica11

 

secca11

FSPTC_SIDE_A_HN = 

 

FSPTC_SIDE_B_HN = 

prica11

 

secca11

EMS_SIDE_A_HN = 

 

EMS_SIDE_B_HN = 

priems11

 

secems11

BDMS_SIDE_A_HN = 

 

BDMS_SIDE_B_HN = 

priems11

 

secems11

Table 15-15

BTSSTAT Command-line Options to Specify Port Numbers to Status 

Command Line Option

Description

Example

-caport <num>

Specify the port number for CA

btsstat -caport 16007

-fsainport <num>

Specify the port number for FSAIN

btsstat -fsainport 16008

-fsptcport <num>

Specify the port number for FSPTC

btsstat -fsptcport 16009

-emsport <num>

Specify the port number for EMS

btsstat -emsport 16010

-bdmsport <num>

Specify the port number for BDMS

btsstat -bdmsport 16011

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands