manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 302

 

7-70

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 7      Maintenance Troubleshooting

Monitoring Maintenance Events

Report Threshold Exceeded—Maintenance (2)

The Report Threshold Exceeded event functions as an informational alert that a report threshold has been 
exceeded. The primary cause of the event is that the threshold for a given report type and number has 
been exceeded. No further action is required since this is an information report. The root cause event 
report

 

threshold should be investigated to determine if there is a service affecting situation. 

Local Side has Become Faulty—Maintenance (3)

The Local Side has Become Faulty alarm (major) indicates that the local side has become faulty. To 
troubleshoot and correct the cause of the Local Side has Become Faulty alarm, refer to the 

“Local Side 

has Become Faulty—Maintenance (3)” section on page 7-92

.

Mate Side has Become Faulty—Maintenance (4)

The Mate Side has Become Faulty alarm (major) indicates that the mate side has become faulty. To 
troubleshoot and correct the cause of the Mate Side has Become Faulty alarm, refer to the 

“Mate Side 

has Become Faulty—Maintenance (4)” section on page 7-92

.

Changeover Failure—Maintenance (5)

The Changeover Failure alarm (major) indicates that a changeover failed. To troubleshoot and correct 
the cause of the Changeover Failure alarm, refer to the 

“Changeover Failure—Maintenance (5)” section 

on page 7-93

.

Changeover Timeout—Maintenance (6)

The Changeover Timeout alarm (major) indicates that a changeover timed out. To troubleshoot and 
correct the cause of the Changeover Timeout alarm, refer to the 

“Changeover Timeout—Maintenance 

(6)” section on page 7-93

.

Mate Rejected Changeover—Maintenance (7)

The Mate Rejected Changeover alarm (major) indicates that the mate rejected the changeover. To 
troubleshoot and correct the cause of the Mate Rejected Changeover alarm, refer to the 

“Mate Rejected 

Changeover—Maintenance (7)” section on page 7-94

.

Mate Changeover Timeout—Maintenance (8)

The Mate Changeover Timeout alarm (major) indicates that the mate changeover timed out. To 
troubleshoot and correct the cause of the Mate Changeover Timeout alarm, refer to the 

“Mate 

Changeover Timeout—Maintenance (8)” section on page 7-97

.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands