Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 628

Page: 628 / 874

15-2

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15 Diagnostic Tests

Media Gateway Tests

Caution

The use of the UNIX

ifconfig down

command on any signaling interface to test or troubleshoot network

or interface failures of the Cisco BTS 10200 Softswitch Signaling Interface may lead to undesirable
consequences or conditions.

Media Gateway Tests

This section describes the tests that can be performed on media gateways. A gateway must be in the
MAINT state.

Step 1

Force the media gateway into MAINT state:

control mgw id=c2421.65; mode=forced; target-state=maint;

Reply Example:

Reply : Success: CLI change successful

MGW ID -> c2421.65

INITIAL STATE -> ADMIN_INS

REQUEST STATE -> ADMIN_MAINT

RESULT STATE -> ADMIN_MAINT

FAIL REASON -> ADM found no failure

REASON -> ADM executed successful

RESULT -> ADM configure result in success

Step 2

Display the Test Menu.

diag mgw

Reply Example:

Reply: Diagnostic MGW Menu.

===

(1) MGW Network Connectivity Test

(2) MGW MGCP Connectivity Test

(3) ALL

Note

Test #1 tests if there is a path to the device (ping).

Test #2 tests if Media Gateway Control Protocol (MGCP) has access to the device.

Test #3 performs tests 1 and 2.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands