manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 406

 

10-38

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Signaling Events and Alarms

SIGNALING (70)

To monitor and correct the cause of the event, refer to the 

“Integrated Services Digital Network Unable 

to Restore D-channel Due to Failed Communication—Signaling (70)” section on page 10-108

.

SIGNALING (71)

To monitor and correct the cause of the event, refer to the 

“Integrated Services Digital Network Unable 

to Establish D-channel—Signaling (71)” section on page 10-108

.

DESCRIPTION

Integrated Services Digital Network Unable to Restore D-channel Due to Failed Communication 
(ISDN Unable to Restore D-channel Due to Failed Communication)

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

0

DATAWORDS

Trunk Group ID–FOUR_BYTES

 

Trunk Group Index–FOUR_BYTES

PRIMARY

 

CAUSE

The ISDN signaling adapter is unable to restore a D-channel due to incorrect backhaul provisioning at 
the media gateway or call agent.

PRIMARY

 

ACTION

Ensure that the provisioning of the backhaul port is correct at both the call agent and media gateway.

DESCRIPTION

Integrated Services Digital Network Unable to Establish D-channel (ISDN Unable to Establish 
D-channel)

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

0

DATAWORDS

Trunk Group ID–FOUR_BYTES

 

Trunk Group Index–FOUR_BYTES

PRIMARY

 

CAUSE

The ISDN signaling adapter is unable to establish a D-channel due to layer one parameters not being 
provisioned correctly or improper provisioning of the network or user side.

PRIMARY

 

ACTION

Verify the correct provisioning at the media gateway.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands