Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 706

Page: 706 / 874

15-80

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15 Diagnostic Tests

Enhanced Traffic Measurement

Table 15-7

Command Line Tokens Associated with Reporting Current Interval Counts

Command Line Token

Description

start-time

A time stamp value with the format of YYYY-MM-DD HH:MM:SS.

This value indicates the starting interval time to search for within the EMS database.

This is a mandatory token.

output

The name of the file to be created and location to place the resulting measurement data.

The file name is pre-pended with the string "Tm_" and placed in the /opt/ems/report directory on
the active EMS.

output-type

The format of the output file—it can be in comma-separated value (csv) or XML format.

call-agent-id

The identity of the call agent that collected the measurement data.

This is an optional token that defaults to all call agents and is only applicable to the following
measurement types:

•

call-tools

•

billing

•

callp

•

mgcp

•

isdn

•

audit

•

sia

•

sim

•

anm

•

h323

•

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands