Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 298

Page: 298 / 874

7-66

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 7 Maintenance Troubleshooting

Monitoring Maintenance Events

This section provides the information needed to monitor and correct maintenance events.

Table 7-2

lists

all of the maintenance events in numerical order and provides cross reference to each subsection in this
section.

Table 7-2

BTS 10200 Maintenance Events

Event Type

Event Name

Event Severity

MAINTENANCE(1)

Test Report—Maintenance (1)

INFO

MAINTENANCE(2)

Report Threshold Exceeded—Maintenance (2)

INFO

MAINTENANCE(3)

Local Side has Become Faulty—Maintenance (3)

MAJOR

MAINTENANCE(4)

Mate Side has Become Faulty—Maintenance (4)

MAJOR

MAINTENANCE(5)

Changeover Failure—Maintenance (5)

MAJOR

MAINTENANCE(6)

Changeover Timeout—Maintenance (6)

MAJOR

MAINTENANCE(7)

Mate Rejected Changeover—Maintenance (7)

MAJOR

MAINTENANCE(8)

Mate Changeover Timeout—Maintenance (8)

MAJOR

MAINTENANCE(9)

Local Initialization Failure—Maintenance (9)

MAJOR

MAINTENANCE(10)

Local Initialization Timeout—Maintenance (10)

MAJOR

MAINTENANCE(11)

Switchover Complete—Maintenance (11)

INFO

MAINTENANCE(12)

Initialization Successful—Maintenance (12)

INFO

MAINTENANCE(13)

Administrative State Change—Maintenance (13)

INFO

MAINTENANCE(14)

Call Agent Administrative State Change—Maintenance (14)

INFO

MAINTENANCE(15)

Feature Server Administrative State Change—Maintenance (15)

INFO

MAINTENANCE(16)

Process Manager: Starting Process—Maintenance (16)

INFO

MAINTENANCE(17)

Invalid Event Report Received—Maintenance (17)

INFO

MAINTENANCE(18)

Process Manager: Process has Died—Maintenance (18)

MINOR

MAINTENANCE(19)

Process Manager: Process Exceeded Restart Rate—Maintenance (19)

MAJOR

MAINTENANCE(20)

Lost Connection to Mate—Maintenance (20)

MAJOR

MAINTENANCE(21)

Network Interface Down—Maintenance (21)

MAJOR

MAINTENANCE(22)

Mate is Alive—Maintenance (22)

INFO

MAINTENANCE(23)

Process Manager: Process Failed to Complete Initialization—Maintenance (23)

MAJOR

MAINTENANCE(24)

Process Manager: Restarting Process—Maintenance (24)

MINOR

MAINTENANCE(25)

Process Manager: Changing State—Maintenance (25)

INFO

MAINTENANCE(26)

Process Manager: Going Faulty—Maintenance (26)

MAJOR

MAINTENANCE(27)

Process Manager: Changing Over to Active—Maintenance (27)

INFO

MAINTENANCE(28)

Process Manager: Changing Over to Standby—Maintenance (28)

INFO

MAINTENANCE(29)

Administrative State Change Failure—Maintenance (29)

WARNING

MAINTENANCE(30)

Element Manager State Change—Maintenance (30)

INFO

MAINTENANCE(32)

Process Manager: Sending Go Active to Process—Maintenance (32)

INFO

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands