manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 191

 

5-5

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 5      Configuration Troubleshooting

Configuration Events and Alarms

CONFIG (7)

To monitor and correct the cause of the event, refer to 

“Application Server Provisioning 

Error—Configuration (7)” section on page 5-7

.

CONFIG (8)

To monitor and correct the cause of the event, refer to 

“BTS 10200 Provisioning for External 

Applications is not Complete—Configuration (8)” section on page 5-7

.

DESCRIPTION

Application Server Provisioning Error

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

0

PRIMARY

 

CAUSE

The external application server has returned a SIP response code that indicates a subscriber is not 
provisioned on the AS.

PRIMARY

 

ACTION

Provision the application server to handle all subscribers which are provisioned on the BTS 10200 to 
use the applications on that server.

DESCRIPTION

BTS 10200 Provisioning for External Applications is not Complete

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

0

PRIMARY

 

CAUSE

The BTS 10200 call agent is provisioned to send a trigger to the feature server for the offhook delay 
trigger (OHD) feature or the terminating attempt trigger (TAT) feature. The subscriber is not 
provisioned to define the sip-trigger-profile ID. 

PRIMARY

 

ACTION

Provision the sip-trigger-profile ID for each subscriber which has OHD or TAT provisioned.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands