manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 482

 

10-114

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Monitoring Signaling Events

Enhanced Subscriber Authentication BTS 10200 Delivery Function Connection 
Down—Signaling (106)

The Enhanced Subscriber Authentication BTS 10200 Delivery Function Connection Down alarm 
(minor) indicates that the enhanced subscriber authentication (ESA) BTS 10200 DF connection is down. 
To troubleshoot and correct the cause of the Enhanced Subscriber Authentication BTS 10200 Delivery 
Function Connection Down alarm, refer to the 

“Enhanced Subscriber Authentication BTS 10200 

Delivery Function Connection Down—Signaling (106)” section on page 10-144

.

Logical Internet Protocol Addresses not Mapped Correctly—Signaling (107)

The Logical Internet Protocol Addresses not Mapped Correctly alarm (critical) indicates that the logical 
IP addresses are not mapped correctly. To troubleshoot and correct the cause of the Logical Internet 
Protocol Addresses not Mapped Correctly alarm, refer to the 

“Logical Internet Protocol Addresses not 

Mapped Correctly—Signaling (107)” section on page 10-145

.

Simplex Only Operational Mode—Signaling (108)

The Simplex Only Operational Mode alarm (major) indicates that the BTS 10200 system can only 
operate in the simplex mode. To troubleshoot and correct the cause of the Simplex Only Operational 
Mode alarm, refer to the 

“Simplex Only Operational Mode—Signaling (108)” section on page 10-145

.

Stream Control Transmission Protocol Association Failure—Signaling (109)

The Stream Control Transmission Protocol Association Failure alarm (major) indicates that the SCTP 
association failed. To troubleshoot and correct the cause of the Stream Control Transmission Protocol 
Association Failure alarm, refer to the 

“Stream Control Transmission Protocol Association 

Failure—Signaling (109)” section on page 10-146

.

Signaling Gateway Group is Out-of-Service—Signaling (110)

The Signaling Gateway Group is Out-of-Service alarm (major) indicates that the signaling gateway 
group is out-of-service. To troubleshoot and correct the cause of the Signaling Gateway Group is 
Out-of-Service alarm, refer to the 

“Signaling Gateway Group Is Out-of-Service—Signaling (110)” 

section on page 10-150

.

Stream Control Transmission Protocol Association Degraded (One of Two 
Internet Protocol Connections Down)—Signaling (111)

The Stream Control Transmission Protocol Association Degraded (One of Two Internet Protocol 
Connections Down) alarm (major) indicates that the SCTP association is degraded. To troubleshoot and 
correct the cause of the Stream Control Transmission Protocol Association Degraded (One of Two 
Internet Protocol Connections Down) alarm, refer to the 

“Stream Control Transmission Protocol 

Association Degraded (One of Two Internet Protocol Connections Down)—Signaling (111)” section on 
page 10-150

.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands