manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 65

 

1-9

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 1      Troubleshooting Overview

Managing Events and Alarms

Managing Events and Alarms

The BTS 10200 generates messages or events to notify you of network conditions. Events with severity 
levels of critical, major, and minor are classified as alarms. Events and alarms are reported to 
the operator console and can be retrieved through command line interface (CLI) commands or a Simple 
Network Management Protocol (SNMP) manager.

The BTS 10200 software writes event and alarm messages to log files that are set up during system 
initialization. This section provides information on using and working with event and alarm log files.

Alarms and informational events produce different system responses.

  •

An alarm is reported whenever an alarmed state changes.

  •

An informational event is reported just once, upon its occurrence, through the operator interfaces 
without any state change being required.

An informational event indicates that a condition worthy of note has occurred. An invalid protocol 
call state transition is an example of an informational event.

This section contains the following:

  •

Managing Event and Alarm Reports, page 1-10

  –

Show Alarm Command, page 1-10

  –

Report Alarm Command, page 1-11

  –

Ack Alarm Command, page 1-12

  –

Clear Alarm Command, page 1-12

  –

Format of Alarm Reports, page 1-13

  •

Events and Alarm Logs, page 1-14

  •

Viewing Event or Alarm Logs, page 1-14

  –

Show, Add, and Delete Event Queue Commands, page 1-16

  •

Saving Events to Log Files, page 1-16

  –

Show Report-Properties Command, page 1-16

  –

Changing Report Properties, page 1-16

  –

Changing Threshold and Throttle Values, page 1-17

  –

Managing and Responding to Events and Alarms, page 1-18

  •

Events and Alarms Descriptions and Corrective Actions, page 1-19

  –

Format of Events and Alarms, page 1-19

Note

Refer to the 

BTS 10200 Command Line Interface Reference Guide

, Release 5.0.x for a detailed 

description of all commands and tokens discussed in this chapter.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands