manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 454

 

10-86

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Signaling Events and Alarms

SIGNALING (165)

To monitor and correct the cause of the event, refer to the 

“No Session Initiation Protocol P-DCS Billing 

Information Header Received—Signaling (165)” section on page 124

.

SIGNALING (166)

To monitor and correct the cause of the event, refer to the 

“No Routing Keys are Active—Signaling 

(166)” section on page 124

.

DESCRIPTION

No Session Initiation Protocol P-DCS Billing Information Header Received (No SIP P-DCS Billing 
Info Hdr Rcvd)

SEVERITY

WARNING

THRESHOLD

10

THROTTLE

0

DATAWORDS

Trunk Group ID–STRING [21]

 

TSAP Address–STRING [65] 

PRIMARY

 

CAUSE

The originating switch is not provisioned to add the P-DCS-Billing-Info header to outgoing SIP 
requests and responses.

PRIMARY

 

ACTION

Provision the originating switch to add the P-DCS-Billing-Info header to outgoing messages.

SECONDARY

 

CAUSE

The header could have been stripped off by an intermediate proxy.

SECONDARY

 

ACTION

Determine if it has been stripped off by an intermediate proxy and configure for corrective action if so.

TERNARY

 

CAUSE

There was a SIP message encode error at the sending switch.

TERNARY

 

ACTION

Determine if a SIP message encode error occurred at the adjacent switch and if so, call the technical 
assistance center to determine a fix for the problem. 

DESCRIPTION

No Routing Keys are Active

SEVERITY

WARNING

THRESHOLD

0

THROTTLE

0

PRIMARY

 

CAUSE

Routing keys are not controlled into an ACTIVE state.

PRIMARY

 

ACTION

Control the routing keys to the ACTIVE state.

SECONDARY

 

CAUSE

The ITP provisioning is incorrect.

SECONDARY

 

ACTION

Check the ITP provisioning.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands