Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 299

Page: 299 / 874

7-67

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 7 Maintenance Troubleshooting

Monitoring Maintenance Events

MAINTENANCE(33)

Process Manager: Sending Go Standby to Process—Maintenance (33)

INFO

MAINTENANCE(34)

Process Manager: Sending End Process to Process—Maintenance (34)

INFO

MAINTENANCE(35)

Process Manager: All Processes Completed Initialization—Maintenance (35)

INFO

MAINTENANCE(36)

Process Manager: Sending All Processes Initialization Complete to
Process—Maintenance (36)

INFO

MAINTENANCE(37)

Process Manager: Killing Process—Maintenance (37)

INFO

MAINTENANCE(38)

Process Manager: Clearing the Database—Maintenance (38)

INFO

MAINTENANCE(39)

Process Manager: Cleared the Database—Maintenance (39)

INFO

MAINTENANCE(40)

Process Manager: Binary Does not Exist for Process—Maintenance (40)

CRITICAL

MAINTENANCE(41)

Administrative State Change Successful with Warning—Maintenance (41)

WARNING

MAINTENANCE(42)

Number of Heartbeat Messages Received is Less Than 50% of
Expected—Maintenance (42)

MAJOR

MAINTENANCE(43)

Process Manager: Process Failed to Come Up in Active Mode—Maintenance (43)

CRITICAL

MAINTENANCE(44)

Process Manager: Process Failed to Come Up in Standby Mode—Maintenance
(44)

CRITICAL

MAINTENANCE(45)

Application Instance State Change Failure—Maintenance (45)

MAJOR

MAINTENANCE(46)

Network Interface Restored—Maintenance (46)

INFO

MAINTENANCE(47)

Thread Watchdog Counter Expired for a Thread—Maintenance (47)

CRITICAL

MAINTENANCE(48)

Index Table Usage Exceeded Minor Usage Threshold Level—Maintenance (48)

MINOR

MAINTENANCE(49)

Index Table Usage Exceeded Major Usage Threshold Level—Maintenance (49)

MAJOR

MAINTENANCE(50)

Index Table Usage Exceeded Critical Usage Threshold Level—Maintenance (50)

CRITICAL

MAINTENANCE(51)

A Process Exceeds 70% of Central Processing Unit Usage—Maintenance (51)

MAJOR

MAINTENANCE(52)

Central Processing Unit Usage is Now Below the 50% Level—Maintenance (52)

INFO

MAINTENANCE(53)

The Central Processing Unit Usage is Over 90% Busy—Maintenance (53)

CRITICAL

MAINTENANCE(54)

The Central Processing Unit has Returned to Normal Levels of
Operation—Maintenance (54)

INFO

MAINTENANCE(55)

The Five Minute Load Average is Abnormally High—Maintenance (55)

MAJOR

MAINTENANCE(56)

The Load Average has Returned to Normal Levels—Maintenance (56)

INFO

MAINTENANCE(57)

Memory and Swap are Consumed at Critical Levels—Maintenance (57)

CRITICAL

MAINTENANCE(58)

Memory and Swap are Consumed at Abnormal Levels—Maintenance (58)

INFO

MAINTENANCE(61)

No Heartbeat Messages Received Through the Interface—Maintenance (61)

CRITICAL

MAINTENANCE(62)

Link Monitor: Interface Lost Communication—Maintenance (62)

MAJOR

MAINTENANCE(63)

Outgoing Heartbeat Period Exceeded Limit—Maintenance (63)

MAJOR

MAINTENANCE(64)

Average Outgoing Heartbeat Period Exceeds Major Alarm Limit—Maintenance
(64)

MAJOR

MAINTENANCE(65)

Disk Partition Critically Consumed—Maintenance (65)

CRITICAL

MAINTENANCE(66)

Disk Partition Significantly Consumed—Maintenance (66)

MAJOR

Table 7-2

BTS 10200 Maintenance Events (continued)

Event Type

Event Name

Event Severity

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands