manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 309

 

7-77

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 7      Maintenance Troubleshooting

Monitoring Maintenance Events

Thread Watchdog Counter Expired for a Thread—Maintenance (47)

The Thread Watchdog Counter Expired for a Thread alarm (critical) indicates that a thread watchdog 
counter has expired for a thread. To troubleshoot and correct the cause of the Thread Watchdog Counter 
Expired for a Thread alarm, refer to the 

“Thread Watchdog Counter Expired for a Thread—Maintenance 

(47)” section on page 7-100

.

Index Table Usage Exceeded Minor Usage Threshold Level—Maintenance (48)

The Index Table Usage Exceeded Minor Usage Threshold Level alarm (minor) indicates that the index 
(IDX) table usage has exceeded the minor threshold crossing usage level. To troubleshoot and correct 
the cause of the Index Table Usage Exceeded Minor Usage Threshold Level alarm, refer to the 

“Index 

Table Usage Exceeded Minor Usage Threshold Level—Maintenance (48)” section on page 7-100

.

Index Table Usage Exceeded Major Usage Threshold Level—Maintenance (49)

The Index Table Usage Exceeded Major Usage Threshold Level alarm (major) indicates that the IDX 
table usage has exceeded the major threshold crossing usage level. To troubleshoot and correct the cause 
of the Index Table Usage Exceeded Major Usage Threshold Level alarm, refer to the 

“Index Table Usage 

Exceeded Major Usage Threshold Level—Maintenance (49)” section on page 7-101

.

Index Table Usage Exceeded Critical Usage Threshold Level—Maintenance 
(50)

The Index Table Usage Exceeded Critical Usage Threshold Level alarm (critical) indicates that the IDX 
table usage has exceeded the critical threshold crossing usage level. To troubleshoot and correct the 
cause of the Index Table Usage Exceeded Critical Usage Threshold Level alarm, refer to the 

“Index Table 

Usage Exceeded Critical Usage Threshold Level—Maintenance (50)” section on page 7-101

.

A Process Exceeds 70% of Central Processing Unit Usage—Maintenance (51)

The A Process Exceeds 70% of Central Processing Unit Usage alarm (major) indicates that a process has 
exceeded the CPU usage threshold of 70 percent. To troubleshoot and correct the cause of the A Process 
Exceeds 70% of Central Processing Unit Usage alarm, refer to the 

“A Process Exceeds 70% of Central 

Processing Unit Usage—Maintenance (51)” section on page 7-101

.

Central Processing Unit Usage is Now Below the 50% Level—Maintenance 
(52)

The Central Processing Unit Usage is Now Below the 50% Level event functions as an informational 
alert that the CPU usage level has fallen below the threshold level of 50 percent. The event is 
informational and no further action is required.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands