manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 407

 

10-39

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Signaling Events and Alarms

SIGNALING (72)

To monitor and correct the cause of the event, refer to the 

“Integrated Services Digital Network–Calls 

Lost Due to D-channel Down for Period of Time—Signaling (72)” section on page 10-108

.

SIGNALING (73)

To monitor and correct the cause of the event, refer to the 

“Integrated Services Digital Network–Unable 

to Send RESTART Due to RESTART Timer Expired—Signaling (73)” section on page 10-108

.

DESCRIPTION

Integrated Services Digital Network–Calls Lost Due to D-channel Down for Period of Time 
(ISDN–Calls Lost Due to D-channel Down for Period of Time)

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

0

DATAWORDS

Trunk Group ID–FOUR_BYTES

 

Trunk Group Index–FOUR_BYTES

PRIMARY

 

CAUSE

The ISDN signaling adapter has lost calls due to a D-channel being down as a result of a media gateway 
power loss or a loss of the connection between the private branch exchange (PBX) and the media 
gateway.

PRIMARY

 

ACTION

Resupply power to the media gateway and verify that the connection between the PBX and the media 
gateway is intact.

DESCRIPTION

Integrated Services Digital Network–Unable to Send RESTART Due to RESTART Timer Expired 
(ISDN–Unable to Send RESTART Due to RESTART Timer Expired)

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

0

DATAWORDS

Termination Name–STRING [40]

 

Termination Index–FOUR_BYTES

 

Trunk Group ID–FOUR_BYTES

 

Trunk Group Index–FOUR_BYTES

 

Restart Class–FOUR_BYTES

PRIMARY

 

CAUSE

The ISDN signaling adapter was unable to send a RESTART message due to the expiration of the 
RESTART timer.

PRIMARY

 

ACTION

Verify that the RESTART timer is set to an appropriate level.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands