Dell Networking S6000 System Скачать руководство пользователя | Manualshive

Страница: 288 / 1510

background image

Related
Commands

— configures a filter to drop packets.

— configures a filter to forward packets.

seq (for IPv6 ACLs)

Assign a sequence number to a deny or permit the filter in an IPv6 access list while creating the filter.

Syntax

seq

sequence-number

{deny | permit} {

ipv6-protocol-number

|

icmp | ip | tcp | udp} {

source address mask

| any | host

ipv6-

address

} {

destination address

| any | host

ipv6-address

}

[

operator port

[

port

]] [count [byte]] [log [interval

minutes

]

[threshold-in-msgs [

count

]] [monitor]

To delete a filter, use the

no seq

sequence-number

command.

Parameters

log

(OPTIONAL) Enter the keyword

log

to enable the triggering

of ACL log messages.

threshold-in
msgs

count

(OPTIONAL) Enter the

threshold-in-msgs

keyword

followed by a value to indicate the maximum number of ACL
logs that can be generated, exceeding which the generation
of ACL logs is terminate with the

seq

,

permit

, or

deny

commands. The threshold range is from 1 to 100.

interval

minutes

(OPTIONAL) Enter the keyword

interval

followed by the

time period in minutes at which ACL logs must be generated.
The interval range is from 1 to 10 minutes.

monitor

(OPTIONAL) Enter the keyword

monitor

when the rule is

describing the traffic that you want to monitor and the ACL
in which you are creating the rule is applied to the monitored
interface.

Defaults

By default, 10 ACL logs are generated if you do not specify the threshold explicitly.

The default frequency at which ACL logs are generated is five minutes. By default,
flow-based monitoring is not enabled.

Command
Modes

ACCESS-LIST

Command
History

Version 9.4(0.0)

Added support for flow-based monitoring on the S4810,
S4820T, S6000, and Z9000 platforms.

Version 9.3(0.0)

Added support for logging of ACLs on the S4810, S4820T,
and Z9000 platforms.

288

Access Control Lists (ACL)

«
...
286
287
288
289
290
...
»

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Networking S6000 System

Бренд: Delta Страницы: 4

Бренд: LONG-JOIN Страницы: 2

Бренд: Watt Stopper Страницы: 10

Бренд: Orno Страницы: 2

Бренд: Fairchild Страницы: 20

SmartStack STS16-20R

Бренд: Cabletron Systems Страницы: 258

Бренд: Orei Страницы: 27

Бренд: G&D Страницы: 80

Бренд: Larson Electronics Страницы: 2

ControlZAPP CZ CESR 10VDC

Бренд: DANLERS Страницы: 2

Бренд: HighSecLabs Страницы: 2

Бренд: TLS Electronics Страницы: 12

IPES-3424DSFP-2P

Бренд: Lantech Страницы: 26

Бренд: ATEN Страницы: 178

Бренд: BJ Live Страницы: 2

SIRCO MOT PV UL

Бренд: socomec Страницы: 20

EX78900X Series

Бренд: EtherWAN Страницы: 2

DG-GS4900SE Series

Бренд: Digisol Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды