Dell Networking S6000 System Скачать руководство пользователя страница 667

Страница: 667 / 1510

Line

Description

– giants = packets that are greater than the MTU size
– throttles = packets containing PAUSE frames

• Number of CRC, overrun, and discarded packets:

– CRC = packets with CRC/FCS errors
– overrun = number of packets discarded due to FIFO

overrun conditions

– discarded = the sum of runts, giants, CRC, and

overrun packets discarded without any processing

Output Statistics:

Displays output statistics sent out of the interface including:

• Number of packets, bytes, and underruns out of the

interface

• Packet size and the number of those packets outbound

to the interface

• Number of Multicast, Broadcast, and Unicast packets:

– Multicasts = number of MAC multicast packets
– Broadcasts = number of MAC broadcast packets
– Unicasts = number of MAC unicast packets

• Number of VLANs, throttles, discards, and collisions::

– Vlans = number of VLAN tagged packets
– throttles = packets containing PAUSE frames
– discarded = number of packets discarded without

any processing

– collisions = number of packet collisions
– wred=count both packets discarded in the MAC and

in the hardware-based queues

Rate information... Estimate of the input and output traffic rate over a

designated interval (30 to 299 seconds). Traffic rate is
displayed in bits, packets per second, and percent of line
rate.

Time since...

Elapsed time since the last interface status change
(hh:mm:ss format).

Example

Dell#show interfaces

TenGigabitEthernet 2/0 is down, line protocol is down

Hardware is DellForce10Eth, address is 00:01:e8:8b:3d:e7

Current address is 00:01:e8:8b:3d:e7

Pluggable media present, Media type is unknown

Wavelength unknown

Interface index is 100992002

Internet address is not set

MTU 1554 bytes, IP MTU 1500 bytes

LineSpeed auto

Flowcontrol rx on tx off

ARP type: ARPA, ARP Timeout 04:00:00

Last clearing of "show interface" counters 3d17h53m

Interfaces

667

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Бренды по названию

Популярные бренды