Dell Networking S6000 System страница 352 Скачать руководство пользователя

Страница: 352 / 1510

events

Enter the keyword

events

to view BGP protocol events.

ipv4

Enter the ipv4 IP address to view the IPV4 route information.

ipv6

Enter the ipv6 IP address to view the IPV6 route information.

keepalives

Enter the keyword

keepalives

to view BGP keepalives.

notifications

Enter the keyword

notifications

to view BGP

notifications.

soft-
reconfiguration

Enter the keywords

soft-reconfiguration

to view only

information on inbound BGP soft reconfiguration.

updates

Enter the keyword

updates

to view BGP updates.

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.4.
(0.0)

Added support for VRF.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

Usage
Information

To view information on both incoming and outgoing routes, do not include the

and

out

parameters in the debugging command. The

and

out

parameters

cancel each other; for example, if you enter the

debug ip bgp in

command and

then enter the

debug ip bgp out

command, you do not see information on the

incoming routes.

Entering a

no debug ip bgp

command removes all configured debug

commands for BGP.

Related
Commands

debug ip bgp events

— views information about BGP events.

debug ip bgp keepalives

— views information about BGP keepalives.

debug ip bgp notifications

— views information about BGP notifications.

debug ip bgp updates

— views information about BGP updates.

352

Border Gateway Protocol

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды