Dell Networking S6000 System Скачать руководство пользователя

Страница: 831 / 1510

Parameters

seconds

The maximum lifetime of LSP in seconds. This value must be
greater than the

lsp-refresh-interval

command. The

higher the value the longer the LSPs are kept. The range is
from 1 to 65535. The default is

1200

Defaults

1200

seconds

Command
Modes

ROUTER ISIS

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version
8.3.12.0

Introduced on the S4810.

Version 8.3.11.1

Introduced on the Z9000.

Usage
Information

Change the maximum LSP lifetime with this command. The maximum LSP lifetime
must always be greater than the LSP refresh interval.

The

seconds

parameter enables the router to keep LSPs for the specified length of

time. If the value is higher, the overhead is reduced on slower-speed links.

Related
Commands

lsp-refresh-interval

— sets the link-state packet (LSP) refresh interval.

maximum-paths

Allows you to configure the maximum number of equal cost paths allowed in a routing table.

S6000

Syntax

maximum-paths

number

To return to the default values, use the

no maximum-paths

command.

Parameters

number

Enter a number as the maximum number of parallel paths an
IP routing installs in a routing table. The range is from 1 to 16.
The default is

Intermediate System to Intermediate System (IS-IS)

831

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды