Dell Networking S6000 System Скачать руководство пользователя | Manualshive

Страница: 272 / 1510

background image

permit arp (for Extended MAC ACLs)

Configure a filter that forwards ARP packets meeting this criteria. This command is supported only on 12-
port GE line cards with SFP optics; refer to your line card documentation for specifications.

Syntax

permit arp {

destination-mac-address mac-address-mask

| any}

vlan

vlan-id

{

ip-address

| any | opcode

code-number

} [count

[byte]] [order] [fragments] [log [interval

minutes

] [threshold-

in-msgs [count]][monitor]

To remove this filter, you have two choices:

• Use the

no seq

sequence-number

command if you know the filter’s

sequence number.

• Use the

{

destination-mac-address mac-address-mask

| any} vlan

vlan-id

{

ip-address

| any | opcode

code-number

}

command.

Parameters

log

(OPTIONAL) Enter the keyword

log

to enable the triggering

of ACL log messages.

threshold-in
msgs

count

(OPTIONAL) Enter the

threshold-in-msgs

keyword

followed by a value to indicate the maximum number of ACL
logs that can be generated, exceeding which the generation
of ACL logs is terminated with the

seq

,

permit

, or

deny

commands. The threshold range is from 1 to 100.

interval

minutes

(OPTIONAL) Enter the keyword

interval

followed by the

time period in minutes at which ACL logs must be generated.
The interval range is from 1 to 10 minutes.

monitor

(OPTIONAL) Enter the keyword

monitor

when the rule is

describing the traffic that you want to monitor and the ACL
in which you are creating the rule is applied to the monitored
interface.

Defaults

By default, 10 ACL logs are generated if you do not specify the threshold explicitly.

The default frequency at which ACL logs are generated is five minutes. By default,
flow-based monitoring is not enabled.

Command
Modes

CONFIGURATION-EXTENDED-ACCESS-LIST

Command
History

Version 9.4(0.0)

Added support for flow-based monitoring on the S4810,
S4820T, S6000, and Z9000 platforms.

Version 9.3(0.0)

Added support for logging of ACLs on the S4810, S4820T,
and Z9000 platforms.

Usage
Information

When the configured maximum threshold is exceeded, generation of logs is
stopped. When the interval at which ACL logs are configured to be recorded
expires, the subsequent, fresh interval timer is started and the packet count for that
new interval commences from zero. If ACL logging was stopped previously
because the configured threshold is exceeded, it is re-enabled for this new interval.

272

Access Control Lists (ACL)

«
...
270
271
272
273
274
...
»

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Networking S6000 System

Бренд: Cabletron Systems Страницы: 88

Бренд: Hama Страницы: 14

Super Speed USB 3.0 Hub

Бренд: Hama Страницы: 14

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 14

Premium Silver USB 2.0 Hub 1:4

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 18

uRage Vendetta 210

Бренд: Hama Страницы: 36

SANbox 5000 Series

Бренд: Qlogic Страницы: 8

Бренд: 6TL Страницы: 25

PIXIE Smart Switch G3

Бренд: SAL Страницы: 2

Бренд: Cross Technologies Страницы: 20

Бренд: Maiwe Страницы: 5

Бренд: DeLOCK Страницы: 8

INTEGRA KLI 310

Бренд: Velux Страницы: 9

Custom Pro Matrix

Бренд: Bluestream Страницы: 27

Бренд: Omron Страницы: 4

Бренд: TAXON TOOLS Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды