Dell Networking S6000 System Скачать руководство пользователя

Страница: 1345 / 1510

Version 9.2(0.0)

Introduced on the M I/O Aggregator. This command is
supported in Programmable-Mux (PMUX) mode only.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version
8.3.10.2

Added support for the

access

parameter.

Version 8.3.7.0

Introduced on the S4810.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

E-Series legacy
command

Usage
Information

The following Example specifies the group named

harig

as a version 3 user

requiring both authentication and encryption and read access limited to the read
named

rview

NOTE: The number of configurable groups is limited to 16 groups.

Example

Dell#conf

Dell(conf)# snmp-server group harig 3 priv read rview

Dell#

Related
Commands

show snmp group

— displays the group name, security model, view status, and

storage type of each group.

show running-config

— displays the SNMP running configuration.

snmp-server host

Configure the recipient of an SNMP trap operation.

S6000

Syntax

snmp-server host

ip-address

ipv6-address

[vrf

vrf-name

] traps

community-string

] [udp-port

port-number

] [

notification-type

]

To remove the SNMP host, use the

no snmp-server host

ip-address

[vrf

vrf-name

priv] [

community-string

] [udp-port

number

] [

notification-type

]

command.

Parameters

ip-address

Enter the keyword

host

then the IP address of the host

(configurable hosts is limited to 16).

Simple Network Management Protocol (SNMP) and Syslog

1345

«
...
1343
1344
1345
1346
1347
...
»

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды