Dell Networking S6000 System Скачать руководство пользователя | Manualshive

Страница: 697 / 1510

background image

Field

Description

Hardware is...

Displays the interface’s hardware information and its
assigned MAC address.

Port-channel is
part...

Indicates whether the LAG is part of a LAG fate-sharing
group (“Failover-group”).

Internet address...

States whether an IP address is assigned to the interface. If
an IP address is assigned, that address is displayed.

MTU 1554...

Displays link and IP MTU.

LineSpeed

Displays the interface’s line speed. For a port channel
interface, it is the line speed of the interfaces in the port
channel.

Members in this...

Displays the interfaces belonging to this port channel.

ARP type:...

Displays the ARP type and the ARP timeout value for the
interface.

Last clearing...

Displays the time when the

show interfaces

counters

were cleared.

Queueing
strategy.

States the packet queuing strategy. FIFO means first in first
out.

packets input...

Displays the number of packets and bytes into the interface.

Input 0 IP
packets...

Displays the number of packets with IP headers, VLAN
tagged headers, and MPLS headers. The number of packets
may not add correctly because a VLAN tagged IP packet
counts as both a VLAN packet and an IP packet.

0 64-byte...

Displays the size of packets and the number of those
packets entering that interface. This information is displayed
over two lines.

Received 0...

Displays the type and number of errors or other specific
packets received. This information is displayed over three
lines.

Output 0...

Displays the type and number of packets sent out the
interface. This information is displayed over three lines.

Rate information... Displays the traffic rate information into and out of the

interface. Traffic rate is displayed in bits and packets per
second.

Time since...

Displays the time since the last change in the configuration
of this interface.

Example

Dell#show interfaces port-channel 20

Port-channel 20 is up, line protocol is up (Failover-group 1

is down)

Hardware address is 00:01:e8:01:46:fa

Port-channel is part of failover-group 1

Internet address is 1.1.120.1/24

MTU 1554 bytes, IP MTU 1500 bytes

Interfaces

697

«
...
695
696
697
698
699
...
»

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Networking S6000 System

Бренд: ABLE Страницы: 5

TotalStorage 3534-F08

Бренд: IBM Страницы: 105

RedBooks SAN24B-5

Бренд: IBM Страницы: 11

RedBooks SAN24B-5

Бренд: IBM Страницы: 2

Бренд: IBM Страницы: 123

8265 Nways ATM Switch

Бренд: IBM Страницы: 192

QuantaMesh T1048-LB9

Бренд: QCT Страницы: 42

Бренд: Server Technology Страницы: 12

Бренд: Black Box Страницы: 4

Бренд: Atlantis Land Страницы: 3

Бренд: Mach Power Страницы: 12

Бренд: Ruby Tech Страницы: 2

LVP-51 LVP-51 Series

Бренд: Omega Engineering Страницы: 6

Бренд: Wavetronix Страницы: 3

UHB-U3P1U2P3P-01

Бренд: Gembird Страницы: 2

Бренд: Crestron Страницы: 36

Бренд: NegoRack Страницы: 41

Бренд: axing Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды