Dell Networking S6000 System страница 852 Скачать руководство пользователя

Страница: 852 / 1510

System Id: F100.E120.0013 IS-Type: level-1-2

Manual area address(es):

49.0000.0001

Routing for area address(es):

49.0000.0001

Interfaces supported by IS-IS:

GigabitEthernet 1/0 - IP - IPv6

GigabitEthernet 1/1 - IP - IPv6

GigabitEthernet 1/10 - IP - IPv6

Loopback 0 - IP - IPv6

Redistributing:

Distance: 115

Generate narrow metrics: level-1-2

Accept narrow metrics: level-1-2

Generate wide metrics: none

Accept wide metrics: none

Multi Topology Routing is enabled in transition mode.

FTOS#

show isis traffic

This command allows you to display IS-IS traffic interface information.

S6000

Syntax

show isis traffic [

interface

]

Parameters

interface

(OPTIONAL) Identifies the interface type slot/port as one of
the following:

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

• For a Gigabit Ethernet interface, enter the keyword

GigabitEthernet

then the slot/port information.

• For a Port Channel interface, enter the keywords

port-

channel

then a number. The range is from 1 to 128.

• For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

then the slot/port information.

• For a VLAN, enter the keyword

vlan

then a number from

1 to 4094.

Command
Modes

• EXEC
• EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

852

Intermediate System to Intermediate System (IS-IS)

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды