Dell Networking S6000 System страница 268 Скачать руководство пользователя | Manualshive

Страница: 268 / 1510

background image

The default frequency at which ACL logs are generated is five minutes. By default,
flow-based monitoring is not enabled.

Command
Modes

CONFIGURATION-MAC ACCESS LIST-STANDARD

Command
History

Version 9.3(0.0)

Added support for logging of ACLs on the S4810, S4820T,
and Z9000 platforms.

Version 9.4(0.0)

Added support for flow-based monitoring on the S4810,
S4820T, S6000, and Z9000 platforms.

Usage
Information

When the configured maximum threshold is exceeded, generation of logs is
stopped. When the interval at which ACL logs are configured to be recorded
expires, the subsequent, fresh interval timer is started and the packet count for that
new interval commences from zero. If ACL logging was stopped previously
because the configured threshold is exceeded, it is re-enabled for this new interval.

If ACL logging is stopped because the configured threshold is exceeded, it is re-
enabled after the logging interval period elapses. ACL logging is supported for
standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure
ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable
logging for ACLs that are associated with egress interfaces.

You can activate flow-based monitoring for a monitoring session by entering the
flow-based

enable

command in the Monitor Session mode. When you enable this

capability, traffic with particular flows that are traversing through the ingress and
egress interfaces are examined and, appropriate ACLs can be applied in both the
ingress and egress direction. Flow-based monitoring conserves bandwidth by
monitoring only specified traffic instead all traffic on the interface. This feature is
particularly useful when looking for malicious traffic. It is available for Layer 2 and
Layer 3 ingress and egress traffic. You may specify traffic using standard or
extended access-lists. This mechanism copies all incoming or outgoing packets on
one port and forwards (mirrors) them to another port. The source port is the
monitored port (MD) and the destination port is the monitoring port (MG).

Related
Commands

— configures a MAC address filter to pass packets.

— configures a MAC address filter with a specified sequence number.

deny (for Extended MAC ACLs)

To drop packets that match the filter criteria, configure a filter.

Syntax

deny {any | host

mac-address

|

mac-source-address mac-source-

address-mask

} {any | host

mac-address

|

mac-destination-address

mac-destination-address-mask

} [

ethertype-operator

] [count

268

Access Control Lists (ACL)

«
...
266
267
268
269
270
...
»

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Networking S6000 System

Бренд: ABB Страницы: 32

Бренд: ABB Страницы: 44

Бренд: ABB Страницы: 15

Бренд: Cabletron Systems Страницы: 88

Бренд: Datavideo Страницы: 58

Бренд: IBM Страницы: 156

Бренд: KELCO Страницы: 4

Бренд: Maipu Страницы: 21

Бренд: Maico Страницы: 56

DSR Series DSR1030

Бренд: Avocent Страницы: 8

S5120-EI Series

Бренд: H3C Страницы: 29

Бренд: C4i Страницы: 7

Бренд: Rackmount Страницы: 16

Бренд: Lanpro Страницы: 16

Бренд: J-Tech Digital Страницы: 81

Бренд: Pulsar Страницы: 5

Бренд: VigilLink Страницы: 24

Бренд: asas Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды