Dell Networking S6000 System Скачать руководство пользователя страница 394

Страница: 394 / 1510

show capture bgp-pdu neighbor

Display BGP packet capture information for an IPv4 address on the system.

S6000

Syntax

show capture bgp-pdu neighbor

ipv4-address

Parameters

ipv4-address

Enter the IPv4 address (in dotted decimal format) of the BGP
address to display packet information for that address.

Command
Modes

EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

Version 7.5.1.0

Introduced.

Example

Dell(conf-router_bgp)#show capture bgp-pdu neighbor 20.20.20.2

Incoming packet capture enabled for BGP neighbor 20.20.20.2

Available buffer size 40958758, 26 packet(s) captured using

680 bytes

PDU[1] : len 101, captured 00:34:51 ago

ffffffff ffffffff ffffffff ffffffff 00650100 00000013

00000000

00000000 419ef06c 00000000

00000000 00000000 00000000 00000000 0181a1e4 0181a25c

41af92c0

00000000 00000000 00000000

00000000 00000001 0181a1e4 0181a25c 41af9400 00000000

PDU[2] : len 19, captured 00:34:51 ago

ffffffff ffffffff ffffffff ffffffff 00130400

PDU[3] : len 19, captured 00:34:51 ago

ffffffff ffffffff ffffffff ffffffff 00130400

[. . .]

Outgoing packet capture enabled for BGP neighbor 20.20.20.2

Available buffer size 40958758, 27 packet(s) captured using

562 bytes

PDU[1] : len 41, captured 00:34:52 ago

ffffffff ffffffff ffffffff ffffffff 00290104 000100b4

394

Border Gateway Protocol

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Бренды по названию

Популярные бренды