Dell Networking S6000 System Скачать руководство пользователя

Страница: 758 / 1510

Fields

Description

Interface

Displays type of interface and the associated slot and port
number.

IP-Address

Displays the IP address for the interface, if configured.

Ok?

Indicates if the hardware is functioning properly.

Method

Displays “Manual” if the configuration is read from the saved
configuration.

Status

States whether the interface is enabled (up) or disabled
(administratively down).

Protocol

States whether IP is enabled (up) or disabled (down) on the
interface.

Example (Brief)

Dell#show ip int brief

Interface IP-Address OK? Method

Status Protocol

GigabitEthernet 1/0 unassigned NO Manual administratively

down down

GigabitEthernet 1/1 unassigned NO Manual administratively

down down

GigabitEthernet 1/2 unassigned YES Manual

up up

GigabitEthernet 1/3 unassigned YES Manual

up up

GigabitEthernet 1/4 unassigned YES Manual

up up

GigabitEthernet 1/5 10.10.10.1 YES Manual

up up

GigabitEthernet 1/6 unassigned NO Manual administratively

down down

show ip management-route

View the IP addresses assigned to the Management interface.

S6000

Syntax

show ip management-route [all | connected | summary | static]

Parameters

all

(OPTIONAL) Enter the keyword

all

to view all IP addresses

assigned to all Management interfaces on the switch.

connected

(OPTIONAL) Enter the keyword

connected

to view only

routes directly connected to the Management interface.

summary

(OPTIONAL) Enter the keyword

summary

to view a table

listing the number of active and non-active routes and their
sources.

758

IPv4 Routing

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды