Dell Networking S6000 System Скачать руководство пользователя

Страница: 843 / 1510

show config

Display the changes you made to the IS-IS configuration. Default values are not shown.

S6000

Syntax

show config

Command
Modes

• ROUTER ISIS (

for IPv4

)

• CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (

for IPv6

)

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.1

Introduced on the S4810.

Example
(Router-Isis)

The bold section identifies that Multi-Topology IS-IS is enabled in Transition mode.

FTOS(conf-router_isis)#show config

router isis

clns host ISIS 49.0000.0001.F100.E120.0013.00

log-adjacency-changes

net 49.0000.0001.F100.E120.0013.00

address-family ipv6 unicast

maximum-paths 16

multi-topology transition

set-overload-bit

spf-interval level-1 100 15 20

spf-interval level-2 120 20 25

exit-address-family

Example
(Address-
Family_IPv6)

The bold section identifies that Multi-Topology IS-IS is enabled in Transition mode.

FTOS(conf-router_isis-af_ipv6)#show conf

address-family ipv6 unicast

maximum-paths 16

multi-topology transition

set-overload-bit

spf-interval level-1 100 15 20

spf-interval level-2 120 20 25

exit-address-family

Intermediate System to Intermediate System (IS-IS)

843

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды