Dell Networking S6000 System страница 671 Скачать руководство пользователя

Страница: 671 / 1510

show interfaces configured

Display any interface with a non-default configuration.

S6000

Syntax

show interfaces configured

Command
Modes

• EXEC
• EXEC Privilege

Command
History

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 8.1.1.0

Introduced on the E-Series ExaScale.

Version 7.6.1.0

Introduced on the S-Series.

Version 7.5.1.0

Introduced on the C-Series.

Version 6.4.1.0

Changed the organization of the display output.

Example

Dell#show interfaces configured

GigabitEthernet 13/18 is up, line protocol is up

Hardware is Force10Eth, address is 00:01:e8:05:f7:fc

Current address is 00:01:e8:05:f7:fc

Interface index is 474791997

Internet address is 1.1.1.1/24

MTU 1554 bytes, IP MTU 1500 bytes

LineSpeed 1000 Mbit, Mode full duplex, Master

ARP type: ARPA, ARP Timeout 04:00:00

Last clearing of "show interfaces" counters 00:12:42

Queueing strategy: fifo

Input Statistics:

10 packets, 10000 bytes

0 Vlans

0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts

0 over 255-byte pkts, 10 over 511-byte pkts, 0 over 1023-

byte pkts

0 Multicasts, 0 Broadcasts

0 runts, 0 giants, 0 throttles

0 CRC, 0 overrun, 0 discarded

Output Statistics:

1 packets, 64 bytes, 0 underruns

1 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts

0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte

pkts

0 Multicasts, 1 Broadcasts, 0 Unicasts

0 Vlans, 0 throttles, 0 discarded, 0 collisions

Rate info (interval 299 seconds):

Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate

Output 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate

Interfaces

671

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды