Dell Networking S6000 System страница 863 Скачать руководство пользователя

Страница: 863 / 1510

Layer 2

This chapter describes commands to configure Layer 2 features.
This chapter contains the following sections:

•

MAC Addressing Commands

•

Virtual LAN (VLAN) Commands

•

The VLAN commands are supported on all the S6000 platform.

MAC Addressing Commands

The following commands are related to configuring, managing, and viewing MAC addresses.

mac-address-table aging-time

Specify an aging time for MAC addresses to remove from the MAC address table.

S6000

Syntax

mac-address-table aging-time

seconds

Parameters

seconds

Enter either zero (0) or a number as the number of seconds
before MAC addresses are relearned. To disable aging of the
MAC address table, enter

. The range is from 10 to

1000000. The default is

1800 seconds

Defaults

1800 seconds

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Layer 2

863

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды