Dell Networking S6000 System Скачать руководство пользователя

Страница: 1465 / 1510

multicast peer-routing timeout

Configure the time for a VLT node to retain synced multicast routes or synced multicast outgoing
interface (OIF) after a VLT peer node failure.

S6000

Syntax

multicast peer-routing timeout

value

To restore the default value, use the

no multicast peer-routing timeout

command.

Parameters

value

Enter the timeout value in seconds. The range is from 1 to
1200. The default is 150.

Command
Modes

VLT DOMAIN (conf-vlt-domain)

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.2(0.0)

Introduced on the M I/O Aggregator. This command is
supported in Programmable-Mux (PMUX) mode only.

Version 9.2(0.2)

Introduced on the Z9000, S4810, and S4820T.

Version 9.0.2.0

Introduced on the S6000.

peer-link port-channel

Configure the specified port channel as the chassis interconnect trunk between VLT peers in the domain.

Syntax

peer-link port-channel

port-channel-number

{peer-down-vlan

vlan

}

Parameters

port-channel-
number

Enter the port-channel number that acts as the interconnect
trunk.

peer-down-
vlan

vlan id

Enter the keyword

peer-down-vlan

then a VLAN ID to

configure the VLAN that the VLT peer link uses when the VLT
peer is down.

Defaults

Not configured.

Command
Modes

VLT DOMAIN

Virtual Link Trunking (VLT)

1465

«
...
1463
1464
1465
1466
1467
...
»

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды