Dell Networking S6000 System Скачать руководство пользователя

Страница: 402 / 1510

show ip bgp community-list

View routes that a specific community list affects.

S6000

Syntax

show ip bgp [vrf

vrf-name

] [

ipv4 unicast

] community-list

community-list-name

[exact-match]

Parameters

vrf

vrf-name

(OPTIONAL) Enter the keywords

vrf

and then the name of

the VRF to view routes affected by a specific community list
corresponding to that VRF.

ipv4 unicast

(OPTIONAL) Enter the keywords

ipv4 unicast

to view

information only related to ipv4 unicast routes.

community-
list-name

Enter the name of a configured IP community list (maximum
140 characters).

exact-match

Enter the keyword for an exact match of the communities.

Command
Modes

• EXEC
• EXEC Privilege

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

The following is a list of the Dell Networking OS version history for this command.

Version 9.4.
(0.0)

Added support for VRF.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

Usage
Information

The

show ip bgp community-list

command without any parameters lists BGP

routes matching the Community List and the output is the same as for the

show

ip bgp

command output.

The following describes the

show ip bgp community-list pass

command

shown in the following example.

402

Border Gateway Protocol

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды